Concept · In development

The Carbon Bath

Straight-on at sunset: teak stairs, open door wall, sink and pill mirror.

It expands

It expands

Packed: rings nested, legs stowed.
Packed: rings nested, legs stowed.
Landing legs swing out and telescope to their feet.
Landing legs swing out and telescope to their feet.
The rings telescope up.
The rings telescope up.
Full height, door still closed.
Full height, door still closed.
Stairs out and the sliding door wall open.
Stairs out and the sliding door wall open.

Deploy animation, straight on: legs, rise, stairs, then the door wall slides open.

Deployed on a mountaintop at sunset, three-quarter view.
Deployed on a mountaintop at sunset, three-quarter view.

Finally, she'll come camping.

The one reason your partner skips the trip is the bathroom. The Carbon Bath gives her a real one: shower, sink and toilet, set up in minutes at camp.

The Carbon Bath travels with any mid-size SUV. Far easier than pulling a trailer.

Packed on a Lexus GX 550, shown for scale.

Packed on a Lexus GX 550, shown for scale.

The Carbon Bath at blue hour, door open and the interior lit.

The Carbon Bath at blue hour, door open and the interior lit.

Earlier iteration, shown for scale.

Earlier iteration, shown for scale.

Engineering

Designed and engineered by Seth Quest: every model, drawing, mechanism and manufacturing detail.

The Carbon Bath is a concept. The drawings, sections and mechanism studies below are Seth’s own design and engineering process, from the current v47f model and the v44–v47 studies that carried into it.

Exploded view rendered from the v47f CAD model: nested wall rings, telescoping posts, sliding wall, floor and pan, stair box and landing legs.

Architecture and plans

Fig. 01Sliding-wall plan, open position. A concept sheet from 30 September 2026: nested wall rings, a sliding wall, and fixture layout. Later work revised the overall plan and the wall stroke; this is not the current v47f drawing set.
Fig. 02Sliding-wall plan, closed position. Same R03 concept sheet as Fig. 01, showing the wall nested for travel.
Fig. 03Top-down floor plan: teak deck, sink, toilet cabinet, sliding-door wall and four landing legs.

Section cuts

Fig. 04Side cutaway of the stowed stair box: nested teak treads and rails in the 1.75 in box.
Fig. 05Cutaway of the stowed stair box, looking down into the cavity: both landing-leg tubes and both teak treads nested in the box.
Fig. 06End section through the stowed stair box at mid-length: the box hung below the floor plate, nested treads, and the landing-leg tubes beside them.
Fig. 07Shower-pan section: a continuous pan falling to one drain, with molded ribs under the teak.

Mechanisms

Fig. 08Stowed stair-box layout, plan and side: treads, rails and slides nested in the box, dimensioned in inches.
Fig. 09Stair engineering study: deploy sequence, side elevation and packing check against the hitch.
Fig. 10Stair mechanism study: stowed in the box, telescoped to the rim, then tilted and locked.
Fig. 11Tread slot-pivot lock schematic, plus the telescope side push-button.
Fig. 12Tread pivot and spring-detent lock (left) and the stair-leg telescope joint (right).
Fig. 13Stair mechanism: the assembly slides out of the box, tilts, and the legs telescope until both teak treads sit level.

Manufacturing details

Fig. 14Stair box hung from the floor plate on four welded L-brackets.
Fig. 15Stair-box L-bracket close-up: fillet weld to the plate and side-accessible bolts into the box wall.
Fig. 16Section through the bracket bolt line: weld to the plate, rivnut in the box wall, bolt clear of the stair slide path.
Fig. 17Stair-tread nose: underside chamfer with an LED slot, and a section through the nose.
Fig. 18Packed underside, current model: landing-leg posts and the stair box under the floor plate.
Fig. 19Roof-plate tab wrapping a telescoping post.